Baker Conversion On Slot Machines

Register here

Slot machines have been on the scene since the late 1800s, with San Francisco mechanic Charles Fey’s Liberty Bell setting the standard as the first reel-spinning game. Companies including Herbert Mills and Bally Industries played key roles in the development of slots, with Bally contributing many innovations. How to market a online casino.

Try some online games that you haven´t seen before in any online casino, that can be found only at. Slot madness casino no deposit bonus codes 2017. Then move on to an exclusive 500% bonus and hit it big with a bankroll that is 5 times your initial deposit! Signup at the casino now and start your winning streak with an exclusive welcome bonus offer bellow which includes a free chip — no deposit bonus. Play unique slot machines with best casino bonuses on offer at.

IGT S+ Slot Machine Game Change

The IGT S+ upright model slot machines use 3 separate pieces of glass. These are the Top or award glass, the middle or reel glass and the bottom or belly glass pieces. These glass pieces are shown in the photo.
When replacing your slot game kit or converting to a different game some kits will include only 2 pieces of glass while others will include all 3 pieces. It really just depends on the game theme. Begin the conversion by removing the top glass. This is done by opening the slot machines main door and carefully lifting up on the glass holder bracket or player tracking bracket that holds the glass in place. Install the new upper glass. If your new kit included the (Reel) glass proceed to remove the old one by removing the florescent lamp bulb and then removing the 3 7/32' florescent fixture screws and finally the fixture itself. Once the fixture is removed you should be able to carefully slide the reel glass out of the machine by grabbing the old reel glass on both sides and carefully wiggle it out of the lower holder and replace it with the new piece of glass. (Be sure that all of your glass decal stickers are securely attached to the new glass pieces before installing the light fixture. Next, the belly or lower glass is replaced by first locating the belly door release knob found on the main door of the machine. Just pull the knob straight out to the right and the belly door will flip down allowing you to remove the the belly glass assembly. You will need to remove the 4 7/32' nuts securing the lighting fixture and then carefully slide the old glass out of the machine. When installing the new belly glass be sure that it is facing right side up with the belly door in its closed position before you tighten up the 7/32' nuts.

Replacing the Slot Reel Strips
Lay out the new strips on a flat surface and take a comparison look at the strips different symbols. If they are all the same and all the symbols line up with each other then you do not need to be concerned with which strip goes to which reel. If however, any strips are different from each other than you will need to install them in the numerical order that specified in the PAR sheet for the game.

The Reels should be numbered in numerical order from left to Right as shown above (1, 2 and 3)
The Reel Strips should also be numbered either on the bottom of the strips or on the back side. The numbers on the reel strips will indicate which strips install into which reel assembly either (1, 2 or 3) depending on your game conversion theme. (Refer to your game theme PAR sheet for specific details) The reel strips will have small notches cut in them at the bottom of the strip. The notches must align with the notches that are molded into each reel basket.

In most cases (Not all) the reel strip showing the lowest number will be installed in the left reel assembly (#1) and the next higher # reel strip will install in the middle reel, etc. If your reel strips contain different symbols on them this rule may not apply.
Locate the notches at the bottom section of the reel strips. You must install the strips aligning these notches with the notches in the reel baskets. The easiest way to do this is to place a reel strip into the left side groove of the basket that it is to be installed into and hold the strip at a 45 degree angle to the basket with one hand and use the other hand to rotate the basket slowly until you feel it catch on the notch. Then, proceed to roll the strip around the back side of the basket and as you do tuck both sides into the grooves of the basket until you come back around to where you started. At this time you want to make sure that the end of the reel strip overlaps the other end of the strip and that they are seated together with the self adhesive sticky surface on the inside of the strip. (You may have to use clear scotch tape to secure the strip to itself. If you did this correctly, you will not be able to see the notches in the strips after you are finished and the reel should spin straight and true. numbers on the bottoms or back sides of the strips so that they are installed in the correct reel.

Slot Machine Eprom Chips

If you change your ‘Game’ eprom you will likely loose the function of the machines bill acceptor and it will require a special set chip to re-activate it. Because of this, most game conversion kits do not require nor include a new game chip as part of the conversion.

Baker Conversion On Slot Machines For Sale

Slot Machines On Facebook

Register here